The Reason Q&A Thread

ehbes · Post by **ehbes** » Sun May 13, 2012 2:35 pm

Could be because of the attack on your sound?

MoonUnit · Post by **MoonUnit** » Sun May 13, 2012 9:29 pm

I found out how to factory reset the device and it started to work again.

Easiest solution for the biggest problem.

However, I can't map kong's drum pads correctly. My controller has 8 soft touch buttons that respond to kong, but pad 2 on the controller corresonds to pad 3 on kong, pad 3 to pad 7, and so on. When I go into keyboard control edit mode it looks as if kong's pads aren't map-able.
Is there no way to map the device as I see fit?

ehbes · Post by **ehbes** » Sun May 13, 2012 10:13 pm

What midi controller is it?

MoonUnit · Post by **MoonUnit** » Mon May 14, 2012 2:52 pm

ehbrums1 wrote:What midi controller is it?

M-Audio Axiom 25 (2nd Generation)

MoonUnit · Post by **MoonUnit** » Mon Jun 18, 2012 5:11 pm

Got Reason 6 not too long ago and I'm new to using the audio tracks.
When I'm layering drum hits, what I used to do was eq/layer the hits, make a small loop of them, bounce to audio, import into audacity, chop the samples + export, then import back into Reason.

Can I completely avoid using audacity now? If so, how do I go about setting up 'capturing' my audio directly from Reason?

Ongelegen · Post by **Ongelegen** » Mon Jun 18, 2012 7:35 pm

MoonUnit wrote:Can I completely avoid using audacity now? If so, how do I go about setting up 'capturing' my audio directly from Reason?

You can select any mix track or audio track as an input onto another audio track by turning on the 'rec source' button of the mix/audio track you want to record. If it's on then it can be selected as input on a audiotrack. You can find this button on the mix/audio track under the small meter when you are in the rack view.

You can also use the sampling input on the back of the hardware interface in you want to record into a sampler (nn-xt, nn-19, kong, redrum). Just route the output of the device you want to record into the sampling input and hit the 'wave' button on the sampler. It's next to the folder button where you load samples.

JTreeZY · Post by **JTreeZY** » Mon Jul 30, 2012 3:04 pm

Anyone know good combinations of devices that would emulate the effects of some 3rd party plug-ins? If you know what i mean...

therapist · Post by **therapist** » Mon Jul 30, 2012 3:06 pm

JTreeZY wrote:Anyone know good combinations of devices that would emulate the effects of some 3rd party plug-ins? If you know what i mean...

You might have to be a bit less vague.

JTreeZY · Post by **JTreeZY** » Mon Jul 30, 2012 3:08 pm

Like what would I do in reason to do what camelphat does?

ehbes · Post by **ehbes** » Mon Jul 30, 2012 3:56 pm

Pulveriser

Fbac · Post by **Fbac** » Sat Aug 04, 2012 7:43 pm

Got an odd problem.. When i export my project (cubase with reason rewired) the reason parts dont fit anymore, even when i export only the reason stuff its about 1/4th behind the rest, yet when i play it normally its fine.

anyone got any ideas on whats going on? (it was fine yesterday and i dont think ive done anything to the settings or anything)

*edit: Fixed temporarily by starting the export on bar 2

ehbes · Post by **ehbes** » Sat Aug 04, 2012 9:08 pm

Could be latency trouble

JTreeZY · Post by **JTreeZY** » Thu Aug 09, 2012 4:18 pm

Any one using the Arpegiator deal with it creating a squeak noise at the beginning of notes. Any one know how to get rid of it

ehbes · Post by **ehbes** » Thu Aug 09, 2012 4:19 pm

Increase the attack in the synth

JTreeZY · Post by **JTreeZY** » Thu Aug 09, 2012 10:22 pm

Anyone know how many DSF Q&As have been with Reason users and know any of their names offhand.. I've seen the Stenchman one thats it

Edit* I'm gunna read all of em anyway, feel free to ignore this question

ehbes · Post by **ehbes** » Fri Aug 10, 2012 2:38 am

Icicles masterclass on YouTube goes over making basses in Thor... Also check out funtcases masterclass but be wary because there is a lot of sketchy info in that one

JTreeZY · Post by **JTreeZY** » Sat Aug 11, 2012 2:37 am

Two questions:

1. When I sample (resample w/e) my basses/synths/drums w/ the NN19, the sample sounds lower in volume. Is there a way to prevent this?

2. How do I make a High pass filter?

ehbes · Post by **ehbes** » Sat Aug 11, 2012 3:02 am

JTreeZY wrote:When I sample (resample w/e) my basses/synths/drums w/ the NN19, the sample sounds lower in volume. Is there a way to prevent this?

m class maximizer

JTreeZY wrote:How do I make a High pass filter?

m class stereo imager- solo hi band- use the freq x over to set the cut off

JTreeZY · Post by **JTreeZY** » Sat Aug 11, 2012 3:09 am

ehbrums1 wrote:
JTreeZY wrote:When I sample (resample w/e) my basses/synths/drums w/ the NN19, the sample sounds lower in volume. Is there a way to prevent this?
m class maximizer

JTreeZY wrote:How do I make a High pass filter?
m class stereo imager- solo hi band- use the freq x over to set the cut off

thanks bro

JTreeZY · Post by **JTreeZY** » Sat Aug 11, 2012 5:06 pm

General Question but no need to make a thread about it since its kind of yes or no. Would just saving a drum hit or synth noise as a wav file and then opening it in a sampler have the same result as sampling it in the sampler?

The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

RPG-8

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

Re: The Reason Q&A Thread

NN19

Re: NN19

Re: NN19

Re: The Reason Q&A Thread

Who is online