Distortion and Stereo Images

neonmansion · Post by **neonmansion** » Thu Jan 10, 2013 3:03 am

Lately I have been noticed that as I process my synths with distortion I lose the stereo information. For example, I had a sound I was making in fm8. I was using two instances of fm8 grouped. They were both slight variations on the same patch and were both panned fairly extreme left and right. The difference in sound in each channel meant that you could hear a fairly wide sounds synth. (very phat)

However, once I started applying distortion to the synths I noticed that the stereo image quickly deteriorated away. Typically I will use ableton's amp or vinyl distortion units. Sometimes ohmicide. Using amp for example made both synths pretty much mono.. each sitting very close to the center of the mix.

Has anyone experienced this and is there an obvious thing I am missing?

bkwsk · Post by **bkwsk** » Thu Jan 10, 2013 3:22 am

Have you checked for phase issues and/or important frequency clashes between the two patches?

neonmansion · Post by **neonmansion** » Thu Jan 10, 2013 3:33 am

no its not the patches.. its that once i apply the distortion modules it loses the stereo image

like say i have a drum rack just playing a hihat panned 50L (all the way to the left).. I see and hear the sound playing all the way only on the left speaker. However if I add in an amp module it becomes almost completely mono..

neonmansion · Post by **neonmansion** » Thu Jan 10, 2013 3:33 am

no its not the patches.. its that once i apply the distortion modules it loses the stereo image

like say i have a drum rack just playing a hihat panned 50L (all the way to the left).. I see and hear the sound playing all the way only on the left speaker. However if I add in an amp module it becomes almost completely mono..

bkwsk · Post by **bkwsk** » Thu Jan 10, 2013 3:35 am

Have you set Amp's output to Dual?

neonmansion · Post by **neonmansion** » Thu Jan 10, 2013 3:38 am

HAHA!1 ... uh damn!

you sir are a genius

neonmansion · Post by **neonmansion** » Thu Jan 10, 2013 3:38 am

what about with vinyl distortion.. there doesn't appear to be a similar option there

bkwsk · Post by **bkwsk** » Thu Jan 10, 2013 3:40 am

Make sure you select Stereo instead of Mono in the Pinch section. Shouldn't do anything strange.

neonmansion · Post by **neonmansion** » Thu Jan 10, 2013 3:42 am

nah its already selected. but when you raise the little circle on the top part or the bottom it goes from stereo to mono.. or at least the panning becomes lost

bkwsk · Post by **bkwsk** » Thu Jan 10, 2013 3:49 am

Yeah, just lower the Drive if that is too extreme. It would be probably due to frequencies overlapping from the waveshapers or something.

ill mindset · Post by **ill mindset** » Thu Jan 10, 2013 6:22 am

http://answers.yahoo.com/question/index ... 101AAzwX5m

bkwsk · Post by **bkwsk** » Thu Jan 10, 2013 2:14 pm

ill mindset wrote:http://answers.yahoo.com/question/index ... 101AAzwX5m

neonmansion · Post by **neonmansion** » Thu Jan 10, 2013 4:06 pm

bkwsk wrote:
ill mindset wrote:http://answers.yahoo.com/question/index ... 101AAzwX5m
(y) anonymous forum bitch

venuq · Post by **venuq** » Fri Jan 11, 2013 6:10 pm

You can always put in a 'utility' and play around with the stereo width of the sound with that.

Distortion and Stereo Images

Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Re: Distortion and Stereo Images

Who is online