Automating the Albino Matrix section values in FL
Posted: Mon Mar 23, 2009 10:55 am
hey guys, does anyone know how to assign this matrix values to your midi controls. Im using FL studio.
peace
peace
welcome
Dubstepforum.com
worldwide dubstep community
https://www.dubstepforum.com/forum/
Automating the Albino Matrix section values in FL
Page 1 of 2
Posted: Mon Mar 23, 2009 11:00 am
What about a nice cup of RTFM ?
welcome
welcome
Posted: Mon Mar 23, 2009 11:02 am
how about you shutting your big mouth since youre no good. you probably have no clue what were talking about. this forum is for folksCheaper wrote:What about a nice cup of RTFM ?
welcome
with a message, now fuck of son. peace
Posted: Mon Mar 23, 2009 11:21 am
good luck with answers since your attitude is kinda puerile and hateful
Posted: Mon Mar 23, 2009 11:54 am
And where is yours?enfant wrote: how about you shutting your big mouth since youre no good. you probably have no clue what were talking about. this forum is for folks
with a message, now fuck of son. peace
Posted: Mon Mar 23, 2009 7:18 pm
flameflameflame
Posted: Mon Mar 23, 2009 8:19 pm
STOP HATING ON THE DUTCH GUY DAMNIT!!! 
Posted: Tue Mar 24, 2009 1:09 pm
thanks for your info. but those things doesnt work ive already tried it. i think that the problem is that fruity doesnt recognise the matrix values as controlable values (ie trough midi), cause when i tweak a matrix value and click on the left menu your talking about then the"last tweaked parameter" is "unclickable".nowaysj wrote:Exactly who should drop the attitude?Depone wrote:jesus. what an introduction. drop the attitude man...enfant wrote:how about you shutting your big mouth since youre no good. you probably have no clue what were talking about. this forum is for folksCheaper wrote:What about a nice cup of RTFM ?
welcome
with a message, now fuck of son. peace
Op asked a question that I haven't heard in my brief tenure here. He's not asking how do you assign the matrix, but how do you link the amount assignment in fl. A Q w/ a twist.
I've never tried to do this, but I'd bet that if its possible, its via the same technique that you use to link all parameters to midi controls in flstudio.
Change the amount value in the matrix, go to the fruity wrapper that houses albino, click that little carrot, go to last tweaked parameter, link to controller, move the controller you want to link it to, and that should be that.
Here's the manual:
http://flstudio.image-line.com/help/html/plugins/Fruity%20Wrapper.htm
Posted: Tue Mar 24, 2009 1:30 pm
^ Mine worked perfectly when I was trying out albino and my copy of albino wasn't even legit - my FL was though.
Posted: Tue Mar 24, 2009 2:31 pm
hmm thats strange... do you got fl 7 or 8? cause use 7.Legendary wrote:^ Mine worked perfectly when I was trying out albino and my copy of albino wasn't even legit - my FL was though.
Posted: Tue Mar 24, 2009 2:37 pm
8 - I can't speak for 7, didn't even know automation to well when I was using that.enfant wrote:hmm thats strange... do you got fl 7 or 8? cause use 7.Legendary wrote:^ Mine worked perfectly when I was trying out albino and my copy of albino wasn't even legit - my FL was though.
Posted: Tue Mar 24, 2009 6:48 pm
i have the same initial problem in 8, so... how do i fix it?
P.S scrolling up to find out is for losers ;>
P.S scrolling up to find out is for losers ;>
Posted: Tue Mar 24, 2009 10:23 pm
I have been trying to workout how you automate the values in the matrix also:/
I know how to create automation for all parts on the albino but you can not go to last changed with the matrix.
I know how to create automation for all parts on the albino but you can not go to last changed with the matrix.
Posted: Tue Mar 24, 2009 10:37 pm
Thats what I am trying to do. I cannot work out how you can automate that value.nowaysj wrote:Even the amount value found inbetween the source and destination?
You can set an lfo to vary the matrix amount, and you can control lfo rate, so by proxy you could control the matrix amount. But I don't wanna blow any gaskets just yet.
Lemme look at this tonight. Any other albino heads know about this?
How can you set the LFO to vary the matrix value?!
At the moment I am sampling each bit I want and just wacking the sample in as a clip. Very limited tho then:/
btw, see the the l1,l2,l3 near the matrix, what does the 'L' stand for?:D